N9LYA has setup a complex system using multi modes and multi ports. Using Packet 1k2 and 9k6, Hf Packet 300Baud, Robust packet, Winmor, Ardop, Pactor, Fldigi, Axip, Telnet.
;N9LYA`s BPQ system Last Edited 9/23/18 (SCS TRACKERS FW V1.7L)
LOCATOR=EM68SR
MAPCOMMENT=BPQ32 Lawrence County In Node, City of Mitchell<BR>All Stations are welcome<BR>n9lya@n9lya.#sin.in.usa.noam
PASSWORD=******
NODECALL=N9LYA-8 ; Node callsign
NODEALIAS=LYANOD ; Node alias (6 characters max)
IDMSG: ; UI broadcast text from NODECALL to fixed dest ID
Node: N9LYA - OPEN-NET - APRS & BBS NETWORK NODE LYANOD/N9LYA-8 Mitchell, IN Lawrence County - MidWest HF Skipnet Hub.
*** ; Denotes end of IDMSG text
BTEXT: ; UI broadcast text from BCALL to destination UNPROTO=
Node: N9LYA-8
BBS: N9LYA
RMS Gateway: K9BBS-10
CHAT Server: K9BBS-14
Midwest HF Skipnet HUB
*** ; Denotes end of BTEXT text
INFOMSG: ; The INFO command text follows:
Type ? for Help BPQ32_6.0.16.30 N9LYA/K9BBS
Type BBS To Access The N9LYA Full Service-BBS:
Type RMS To Access The K9BBS-10 WL2K RMS Gateway:
Type CHAT TO Access The K9BBS-14 CHAT Server:
Type DX TO Access The N9LYA-6 DX Spider Server:
*** ; Denotes end of INFOMSG text
CTEXT: ; The CTEXT text follows:
Welcome to LYANOD:N9LYA-7 Network Node Server, Mitchell, Indiana
Commands:
BBS RMS CHAT DX JNOS URONOD MSYS CONNECT INFO MHEARD LISTEN (port) NODES PORTS ROUTES USERS
*** ; Denotes end of CTEXT text
FULL_CTEXT=0 ; 0=send CTEXT to L2 connects to NODEALIAS only
; 1=send CTEXT to all connectees
; Network System Parameters:
OBSINIT=6 ; Initial obsolescence set when a node is included
; in a received nodes broadcast. This value is then
; decremented by 1 every NODESINTERVAL.
OBSMIN=4 ; When the obsolescence of a node falls below this
; value that node`s information is not included in
; a subsequent nodes broadcast.
NODESINTERVAL=20 ; Nodes broadcast interval in minutes
IDINTERVAL=10 ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
BTINTERVAL=60 ; The BTEXT broadcast interval in minutes, 0=OFF
L3TIMETOLIVE=25 ; Max L3 hops
L4RETRIES=3 ; Level 4 retry count
L4TIMEOUT=60 ; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=2 ; Level 4 delayed ack timer in seconds
L4WINDOW=4 ; Level 4 window size
MAXLINKS=63 ; Max level 2 links
MAXNODES=550 ; Max nodes in nodes table
MAXROUTES=64 ; Max adjacent nodes
MAXCIRCUITS=128 ; Max L4 circuits
MINQUAL=143 ; Minimum quality to add to nodes table
MAXHOPS=4 ; INP3 hop limit to add to tables
MAXRTT=90 ; INP3 max RTT in seconds
; possible, normally about 130, depending upon other
; table sizes.
;
; TNC default parameters:
PACLEN=236 ; Max packet size (236 max for net/rom)
LINMAIL
LINCHAT
/*
PACLEN is a problem! The ideal size depends on the link(s) over which a packet
will be sent. For a session involving another node, we have no idea what is at
the far end. Ideally each node should have the capability to combine and then
refragment messages to suit each link segment - maybe when there are more BPQ
nodes about than 'other' ones, I'll do it. When the node is accessed directly,
things are a bit easier, as we know at least something about the link. So,
currently there are two PACLEN params, one here and one in the PORTS section.
This one is used to set the initial value for sessions via other nodes and for
sessions initiated from here. The other is used for incoming direct (Level 2)
sessions. In all cases the TNC PACLEN command can be used to override the
defaults.
*/
; Level 2 Parameters:
; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section
T3=120 ; Link validation timer in seconds
IDLETIME=3600 ; Idle link shutdown timer in seconds
; Configuration Options:
AUTOSAVE=1 ; Saves BPQNODES.dat upon program exit
BBS=1 ; 1 = BBS support included, 0 = No BBS support
NODE=1 ; Include switch support
HIDENODES=1 ; If set to 1, nodes beginning with a #
; require a 'N *' command to be displayed.
; The *** LINKED command is intended for use by gateway software, and concern
; has been expressed that it could be misused. It is recommended that it be
; disabled (=N) if unneeded.
ENABLE_LINKED=A ; Controls processing of *** LINKED command
; Y = allows unrestricted use
; A = allows use by application program
; N = disabled
;
;
IPGATEWAY
Adapter eth1
44ENCAP 192.168.1.17
IPADDR 44.48.0.42
IPNetmask 255.255.255.248
IPPorts 3,5,8,9,10,11,12,13
****
;
;
;-----------------------------
; BPQAPRS
APRSDIGI
APRSCall N9LYA-3
StatusMsg=BPQ32 VHF-APRS/wview-WMR968-Weather Station. {linbpq}
Symbol=_ ; Icon to display for station. Default is House if omitted
Symset=/
;
; Specify a Dest and Path for each port you want to use for APRS. No dest means receive only port
; Ports without an APRSPath statement will not be used by the Digi
;
;APRSPath 1=APRS,WIDE1-1,WIDE2-2
APRSPath 1=APRS,IN1-1 ;Per Dwight
APRSPath 2= ; Receive only port
APRSPath 3=
APRSPath 4=
APRSPath 5=
APRSPath 6=
APRSPath 7=
APRSPath 8=
APRSPath 9=
APRSPath 10=
APRSPath 11=
APRSPath 12=APRS,WIDE1-1,WIDE2-2
APRSPath 13=
APRSPath 14=
APRSPath 15=
APRSPath 16=
APRSPath 17=
APRSPath 18=APRS,WIDE1-1,WIDE2-2
APRSPath 19=
;
BeaconInterval=30 ; Send Beacon every 30 minute
; Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
; If a Digimap isn`t specified for a port, digi out on the port the packet arrived on,
; and send to APRS-IS (if enabled)
; If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n
;Digimap 5=5,16, ; Packets from 5 to 16, but not APRS-IS
Digimap 1=1, ; Packets from 1 to 1 and NO APRS-IS
;TraceCalls=WIDE,TRACE ; Calls for CALLN-n Processing with Trace
TraceCalls=WIDE,IN ; Calls for CALLN-n Processing with Trace
FloodCalls=LYA ; Calls for CALLN-n Processing without Trace
DigiCalls=n9lya-3 ; Calls for Normal (ie no SSID manipulation) Digi
; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
ReplaceDigiCalls ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
MaxTraceHops=2 ; Max value of n in CALLN-n processing. If a packet is received with n greater than
MaxFloodHops=2 ; this, the value will be replaced BEFORE it is decremented.
; GPSPort=/dev/ttyACM0 ; if specified, lat/lon will be taken from a GPS
; GPSSpeed=9600
; GPSSetsLocator=1
; You can specify a fixed LAT/LONG instead of using GPS
LAT=3844.42N ; Must be in standard APRS Format
LON=08628.33W ; Must be in standard APRS Format
;IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS
;ISHost=rotate.aprs.net ; APRS-IS Host Name
;ISPort=14580 ; Normal port for a filtered feed
;ISPasscode=12418 ; If you don`t already have a passcode I can issue you one.
;WXFileName=/dev/shm/aprs.pkt
WXFileName=/var/www/mitchellwx/formateddata.txt
WXComment=/MITWXN Mitchell IN N9LYA-3 KINMITCH1 Weather Station (linBPQ)
WXPortList=1 ; comma separated list - include IS to send to APRS-IS
WXInterval=3 ; mins
***
; Port Definitions:
PORT ;144.390 APRS 1200
PORTNUM=1
ID=APRS 144.390 Icom2200H ; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS mode
FULLDUP=0 ; Only meaningful for KISS devices
COMPORT=/dev/ttyUSB7 ; # = SERIAL COM PORT
SPEED=38400 ; RS232 COM PORT SPEED
CHANNEL=A ; A for single channel TNC, A or B for multichannel
PERSIST=230 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=100 ; CMSA interval timer in milliseconds
TXDELAY=350 ; Transmit keyup delay in milliseconds
TXTAIL=0 ; TX key down, in milliseconds, at packet end
QUALITY=0 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=95 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=2 ; Max outstanding frames (1 thru 7)
FRACK=6000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=5 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=: ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=N9LYA ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digi`d frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
ENDPORT
;
;
;
PORT ;
PORTNUM=2 ; Optional but sets port number if stated
ID=OpenNET 223.600 9.6k Backup
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS mode
NOKEEPALIVES=1
FULLDUP=1 ; Only meaningful for KISS devices
COMPORT=/dev/ttyUSB7 ; # = SERIAL COM PORT
SPEED=38400 ; RS232 COM PORT SPEED
CHANNEL=B ; A for single channel TNC, A or B for multichannel
PERSIST=64 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=100 ; CMSA interval timer in milliseconds
TXDELAY=250 ; Transmit keyup delay in milliseconds
TXTAIL=0 ; TX key down, in milliseconds, at packet end;
QUALITY=192 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=175 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=4 ; Max outstanding frames (1 thru 7)
FRACK=2000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=15 ; Level 2 maximum retry value
PACLEN=64 ; Default max packet length for this port
UNPROTO=Node: ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=n9lya-7 ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digi`d frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
NOKEEPALIVES=1
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 223600000, PKT9600, 60, 35, 9
ENDPORT
;
;
PORT ; AXIP/UDP Port (Internet Link)
PORTNUM=3 ; Optional but sets port number if stated
ID=AX/IP/UDP (Internet Linking) ; Displayed by PORTS command
TYPE=EXTERNAL ; Calls an external module
DRIVER=BPQAXIP ; Uses BPQAXIP.DLL
QUALITY=192 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=168 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=5 ; Max outstanding frames (1 thru 7)
FRACK=5000 ; Level 2 timout in milliseconds
RESPTIME=1500 ; Level 2 delayed ack timer in milliseconds
RETRIES=5 ; Level 2 maximum retry value
PACLEN=236 ; Max = 236
NOKEEPALIVES=1
DIGIFLAG=1
DIGIPORT=14
CONFIG
UDP 10093
MHEARD ;Opens AXIP MHEARD window
AUTOADDMAP
BROADCAST NODES
BROADCAST QST
MAP W9ABA-7 *.*.*.* udp 10093 B
MAP AE5E-14 *.*.*.* UDP 10093 B
MAP n0kfq-4 *.*.*.* UDP 10093 B
MAP N4ZKF-5 *.*.*.* UDP 10093 B
MAP KQ0I-7 *.*.*.* UDP 10093 B
MAP VK2DOT *.*.*.* UDP 10093 B
MAP K7MT *.*.*.* UDP 10093 B
MAP KB8PMY-5 *.*.*.* UDP 10093 B
MAP N9UMJ-7 *.*.*.* UDP 10093 B
MAP KJ6IX-4 *.*.*.* UDP 10093 B
;-----------------------------------------------------------------
;
PORT
PORTNUM=4
ID=HF_SkipNET Pactor 746Pro
TYPE=EXTERNAL
COMPORT=/dev/ttyUSB10 ; # = SERIAL COM PORT
SPEED=57600 ;COM Port Speed
DLLNAME=SCSPactor.DLL
QUALITY=0
INTERLOCK=4 ;Optional - set if you have two ports sharing the same radio.
; Set the same Interlock value on both ports.
CONFIG ; Driver-Specific Configuration
RIGCONTROL
/dev/746-RC 19200 ICOM IC746 66
7,3.58700,usb,f1,d,p123,w2
7,14.11100,usb,F1,d,p123,w2
7,18.10800,usb,F1,d,p123,w2
****
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 3587000, P123, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, P123, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, ARDOP1000, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, P12, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, ARDOP500, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, WINMOR1600, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, WINMOR500, 50, 50, 6 6
#
# Note that the PTC is sent the RESTART command before being initialised, so only non-default
# parameters need to be set
#
PAC BAUD 300 ; Sets the PTC Packet Modem to Packet Mode
PAC TXD 600
SCANFORROBUSTPACKET 7 ; The PTC will listen for HF Packet calls for the first n seconds
# ; of each scan interval, and for Pactor the rest.
PAC MCON 6
PAC MON 6
#
UseAPPLCallsforPactor
TONES 4 ; Standard Pactor III tones 1500 Hz audio center
MAXERR 60 ; Max retries
MODE 2 ; ASCII mode, no PTC II compression (Forwarding will use FBB Compression)
MAXSUM 60 ; Max count for memory ARQ
MAXDOWN 5
MAXLEVEL 3
MAXT 2
MAXUP 3
CWID 0 2 ; CW ID disabled
ADDLF 0 ; Auto Line Feed disabled
ARX 1 ; Amtor Phasing disabled
AP 100 ;
AQ 1 ; Automatic Frequency Parameter
BELL 1 ; Disable Bell
BC 0 ; FEC reception is disabled
BR 7 ;
BKCHR 2 ; Breakin Char = 2
CHOBELL 1 ; Changeover Bell off
CMSG 0 ; Connect Message Off
CONT 3
CWID 0 3
CWSPEED 100
FREE MODE 0
LFIGNORE 0 ; No insertion of Line feed
LISTEN 1 ; Pactor Listen disabled
LSB
MAIL 0 ; Disable internal mailbox reporting
MYCALL N9LYA ;
MYSELC NLYA ;
REMOTE 0 ; Disable remote control
FSKA 750 ;
PSKA 750 ; TX Output level. May need optimising. Default is 140
STATUS 2 ; Automatic Status must be enabled for BPQ32
PTCHN 31 ; Pactor must use Host Mode Chanel 31
PDUPLEX 1 ; PDuplex must be set. The Node code relies on automatic IRS/ISS changeover
PDTIMER 6 ; 5 second duplex timer
BUSYHOLD 8 ;Busy Detect Augmentation
BUSYWAIT 12 ;
ENDPORT
;
PORT ; 440 9600 Baud
PORTNUM=5 ; Optional but sets port number if stated
ID=OpenNET 432.250 9.6k TEKK; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS mode
NOKEEPALIVES=1
FULLDUP=0 ; Only meaningful for KISS devices
COMPORT=/dev/ttyUSB8 ; # = SERIAL COM PORT
SPEED=19200 ; RS232 COM PORT SPEED
CHANNEL=A ; A for single channel TNC, A or B for multichannel
PERSIST=64 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=50 ; CMSA interval timer in milliseconds
TXDELAY=150 ; Transmit keyup delay in milliseconds
TXTAIL=100 ; TX key down, in milliseconds, at packet end
QUALITY=192 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=175 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=2 ; Max outstanding frames (1 thru 7)
FRACK=4000 ; Level 2 timout in milliseconds
RESPTIME=100 ; Level 2 delayed ack timer in milliseconds
RETRIES=15 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=Node: ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=N9LYA-8 ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digi`d frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 432250000, PKT9600, 35, 35, 9, 205
ENDPORT
;
PORT
PORTNUM=6
ID=Skipnet RPR/HF 706MKIIG;(RPR and HF Packet) ;COM30
TYPE=EXTERNAL
COMPORT=/dev/TrackerN40
SPEED=38400
DLLNAME=SCSTRACKER.DLL
INTERLOCK=6
CONFIG
;APPL BBS
RIGCONTROL
/dev/706-RC 19200 ICOM IC706 58
7,7.1010,usb,F1,r2,w2
7,7.1030,usb,F1,r2,w2
7,7.1095,lsb,F1,h1,w1
****
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 7104500, ROBUST, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 7102500, ROBUST, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 7102500, WINMOR500, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 7102500, ARDOP500, 50, 35, 3
#
O 4 ; MAXFRAME
F 190 ; FRACK
T 8 ; TX Delay
DEFAULT ROBUST ; Default mode is RP
USEAPPLCALLS ; Accept connects to all APPLCALLS
%L 1500 ; Centre Freq for Normal Packet (Default is 1500)
@I 64 ;Paclen = 60
%T 1 :TX Autotracking 1 = on
%N 10
ENDPORT
;
PORT
PORTNUM=7
ID=Telnet Server
Driver=Telnet
CONFIG
LOGGING=1
DisconnectOnClose=1
TCPPORT=8010
FBBPORT=8011 8012 8013 8014
LOGINPROMPT=user:
PASSWORDPROMPT=password:
MAXSESSIONS=26 ;was 12
HTTPPORT=8080
CMS=1
CMSCALL=K9BBS
CMSPASS=*********
CTEXT=Welcome to K9BBS`s Telnet Server\Enter ? for list of commands
USER=N9LYA,********,N9LYA,"",SYSOP
ENDPORT
;
;
PORT
PORTNUM=8 ; WINMOR port Tracker Pair
ID=Skipnet WINMOR 706MKIIG 7.101U
TYPE=EXTERNAL
PROTOCOL=WINMOR
DLLNAME=WINMOR.DLL
INTERLOCK=6
QUALITY=0
CONFIG ; Winmor config
ADDR 192.168.1.12 18500 PATH REMOTE:C:\WINMORII\WINMOR TNC.EXE
CAPTURE USB audio CODEC-01
PLAYBACK USB audio CODEC-01
CWID FALSE
DEBUGLOG True
BW 1600
DRIVELEVEL 100
MODE AUTO
ROBUST False
SHOW True
BUSYLOCK False
BUSYHOLD 5
BUSYWAIT 12
ENDPORT
;
;
PORT
PORTNUM=9 ; WINMOR port Pactor Pair
ID=Skipnet WINMOR 746Pro 14.111U
TYPE=EXTERNAL
PROTOCOL=WINMOR
DLLNAME=WINMOR.DLL
INTERLOCK=4
QUALITY=0
CONFIG ; Winmor config
ADDR 192.168.1.12 18600 PATH REMOTE:C:\WINMOR\WINMOR TNC.EXE
CAPTURE USB audio CODEC-02
PLAYBACK USB audio CODEC-02
CWID FALSE
DEBUGLOG True
BW 1600
DRIVELEVEL 100
MODE AUTO
ROBUST False
SHOW True
BUSYLOCK False
BUSYHOLD 5
BUSYWAIT 12
ENDPORT
;
;
PORT
PORTNUM=10
ID=OpenNET 223.600 9.6k
COMPORT=/dev/555; COM Port Address
SPEED=38400; COM Port Speed
DRIVER=TRKMULTI
QUALITY=192 ;Setting to 0 stops node broadcasts on this port
MINQUAL=175
PACLEN=128 ;Max = 236 if using NETROM links
CONFIG ; Driver-Specific Configuration
M UISC
PACKETCHANNELS 5 ; Limit to 5 simultaneous connections
R 0 ; Digipeating OFF
F 600 ; FRACK: Setting to 3 seconds.
N 10 ; RETRY: Setting to 10
O 2 ; MAXFRAME: Setting to 2
T 35 ; TXDELAY: Setting to 1/2 second (50 * 10)
@T2 150 ; RESPTIME: Setting interval before ack of received packet to 1.5 seconds.
%N 5 ; TXTAIL - new TXTAIL (fw 1.5v) setting in 10ms increments.
; Comment out the desired speed.
;%B 1200 ; 1200 is the poweron default, but setting it anyway.
%B 9600 ; 9600
;
%L +500 ; AFSK
%XA 880 ; Set 300/1200 output amplitude to 3 kHz Peak deviation per measurement.
%XF 1600 ; Set 9600/19k2 output amplitude to 400 mV PP per ID-880H manual.
%E 2 ; Set lower tone in 1200 mode (fw 1.5s) to 1/2 voltage 6 dB down from high.
ENDPORT
;
;
PORT
PORTNUM=11
ID=OpenNET 145.050 1.2k
COMPORT=/dev/050; COM Port Address
SPEED=38400; COM Port Speed
DRIVER=TRKMULTI
QUALITY=192 ;Setting to 0 stops node broadcasts on this port
MINQUAL=175
PACLEN=128 ;Max = 236 if using NETROM links
CONFIG ; Driver-Specific Configuration
M UISC
PACKETCHANNELS 5 ; Limit to 5 simultaneous connections
R 0 ; Digipeating OFF
F 600 ; FRACK: Setting to 3 seconds.
N 10 ; RETRY: Setting to 10
O 2 ; MAXFRAME: Setting to 2
T 35 ; TXDELAY: Setting to 1/2 second (50 * 10)
@T2 150 ; RESPTIME: Setting interval before ack of received packet to 1.5 seconds.
%N 5 ; TXTAIL - new TXTAIL (fw 1.5v) setting in 10ms increments.
; Comment out the desired speed.
%B 1200 ; 1200 is the poweron default, but setting it anyway.
;%B 9600 ; 9600
;
%L +500 ; AFSK
%XA 880 ; Set 300/1200 output amplitude to 3 kHz Peak deviation per measurement.
%XF 1200 ; Set 9600/19k2 output amplitude to 400 mV PP per ID-880H manual.
%E 2 ; Set lower tone in 1200 mode (fw 1.5s) to 1/2 voltage 6 dB down from high.
ENDPORT
;
;
PORT
PORTNUM=12
ID=Tracker 10.1473 USB ;(RPR APRS)
TYPE=EXTERNAL
COMPORT=/dev/098
SPEED=38400
DLLNAME=SCSTRACKER.DLL
INTERLOCk=12
CONFIG
****
#
O 4 ; MAXFRAME
F 190 ; FRACK
T 8 ; TX Delay
DEFAULT ROBUST ; Default mode is RP
USEAPPLCALLS ; Accept connects to all APPLCALLS
%L 1500 ; Centre Freq for Normal Packet (Default is 1500)
@I 64 ;Paclen = 60
%T 1 :TX Autotracking 1 = on
%N 10
ENDPORT
;
;
PORT
PORTNUM=13
ID=HF_Skipnet NET105 ;(RPR and HF Packet Pair) 14.105
TYPE=EXTERNAL
COMPORT=/dev/105;
SPEED=38400
DLLNAME=SCSTRACKER.DLL
INTERLOCK=13
CONFIG
****
#
O 4 ; MAXFRAME
F 700 ; FRACK
T 50 ; TX Delay
DEFAULT HFPACKET ; Default mode is 300 Baud Packet
USEAPPLCALLS ; Accept connects to all APPLCALLS
%L 1500 ; Centre Freq for Normal Packet (Default is 1500)
@I 64 ;Paclen = 60
%T 1 :TX Autotracking 1 = on
%N 10
ENDPORT
;
;
PORT
PORTNUM=14
ID=HF_Skipnet ARDOP1 706MKIIG
DRIVER=ARDOP
INTERLOCK=6
CONFIG
ADDR 192.168.1.12 8520 PATH REMOTE:C:\ARDOP1\ARDOP_WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0
ENDPORT
;
;
PORT
PORTNUM=15
ID=HF_Skipnet ARDOP1 746Pro
DRIVER=ARDOP
INTERLOCK=4
CONFIG
ADDR 192.168.1.12 8515 PATH REMOTE:C:\ARDOP2\ARDOP_WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0
ENDPORT
;
;
PORT
PORTNUM=16
ID=HF_Skipnet ARDOP2 746Pro
DRIVER=ARDOP
INTERLOCK=4
CONFIG
ADDR 192.168.1.12 8522 PATH REMOTE:C:\ARDOP1\ARDOP_2WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0
ENDPORT
;
;
PORT
PORTNUM=17
ID=HF_Skipnet ARDOP2 706MKIIG
DRIVER=ARDOP
INTERLOCK=6
CONFIG
ADDR 192.168.1.12 8526 PATH REMOTE:C:\ARDOP2\ARDOP_2WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0
ENDPORT
;
;
PORT
PORTNUM=18
ID=OpenNET ARDOP 147.555
DRIVER=ARDOP
INTERLOCK=16
CONFIG
ADDR 127.0.0.1 8517 PATH /home/jerry/ardop/ardopc 8517
CAPTURE USB audio CODEC
PLAYBACK USB audio CODEC
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0
ENDPORT
;
/*
;
PORT
PORTNUM=19
ID=FLDigi-1 OpenNET
DRIVER=fldigi
PACLEN=64
INTERLOCK=8
CONFIG
ADDR 192.168.1.12 7342 PATH REMOTE:C:\FLDIGI\FLDIGI.exe
TIMEOUT=10
RETRIES=5
DEFAULTMODEM MFSK32/1000 ;5XPSK63R/1000
UPDATEMAP
ENDPORT
;
;
;
PORT
PORTNUM=20
ID=FLDigi-2 OpenNET
DRIVER=fldigi
PACLEN=64
INTERLOCK=12
CONFIG
ADDR 192.168.1.12 7442 PATH REMOTE:C:\FLDIGIII\FLDIGI.exe
TIMEOUT=10
RETRIES=15
DEFAULTMODEM MFSK32/1500 ;5XPSK63R/1000
UPDATEMAP
ENDPORT
;
*/
;
PORT
PORTNUM=19 ;loopback
TYPE=INTERNAL
ENDPORT
;
;
ROUTES: ; Locked routes (31 maximum)
;N9PMO-2,1,3,0,0,0,1
;
; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN]
; The values in [...] if stated override the port defaults.
*** ; Denotes end of locked routes
;
APPLICATION 1,BBS,,N9LYA,INBBS,255
APPLICATION 2,RMS,C 7 CMS,K9BBS-10,INRMS,255
APPLICATION 3,CHAT,,K9BBS-14,INCHAT,255
APPLICATION 4,DX,C 3 DXLYA s,N9LYA-6,255
APPLICATION 5,JNOS,C 3 INNOS s,N9LYA-5,255
APPLICATION 6,FBB,C 3 BBSLYA s,n9lya-4,255
APPLICATION 7,URONOD,C 3 IN105 s,N9LYA-7,255
APPLICATION 8,MSYS,C 3 BBSBBS,W9BBS,255