;*\
;Packet/Switch netwerk Kortgene.
;*/
LOCATOR=JO11VN
MAPCOMMENT=PI1LAP-7 Network Node, Kortgene JO11VN
PASSWORD=*****
NODECALL=PI1LAP-7 ; Node callsign
NODEALIAS=NDRLND ; Node alias (6 characters max)
IDMSG:
PI1LAP-7 - PI8LAP - JO11VN
***
BTEXT: ; UI broadcast text from BCALL to destination UNPROTO=
PI1LAP-7 - PI8LAP((Lin)BPQ) Ax25 - Net/rom - BBS - JO11VN
***
INFOMSG: ; The INFO command text follows:
PI1LAP-7:PI8LAP LinBPQ Packet/Switch Node
Computer : Raspberry PI 3B
Software : Raspbian GNU/Linux 10 / Linbpq 6.0.24.*
Rx/Tx : Icom 7300 / Yaesu FT7900
Modem : Scs PTC11pro / Qtsoundmodem 300 Baud / Ardopc / Vara / il2p
Antenne : HyendFed 20m / X-510n
***
CTEXT: ; The CTEXT text follows:
Connected to PI1LAP-7,
PI1LAP-7 > BBS,RMS,C,B,I,N,R,P,U,V,S,MH
*** ; Denotes end of CTEXT text
MQTT=1
MQTT_HOST=44.137.31.76
MQTT_PORT=1883
MQTT_USER=pd9q
MQTT_PASS=********
HFCTEXT=HF node PI1LAP-7
EnableM0LTEMap=1
FULL_CTEXT=1 ; 0=send CTEXT to L2 connects to NODEALIAS only
; 1=send CTEXT to all connectees
OBSINIT=6 ; Initial obsolescence set when a node is included
; in a received nodes broadcast. This value is then
; decremented by 1 every NODESINTERVAL.
OBSMIN=4 ; When the obsolescence of a node falls below this
; value that nodes information is not included in
; a subsequent nodes broadcast.
NODESINTERVAL=25 ; Nodes broadcast interval in minutes
IDINTERVAL=10 ; IDMSG UI broadcast interval in minutes, 0=OFF
BTINTERVAL=15 ; The BTEXT broadcast interval in minutes, 0=OFF
L3TIMETOLIVE=25 ; Max L3 hops
L4RETRIES=5 ; Level 4 retry count
L4TIMEOUT=60 ; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=10 ; Level 4 delayed ack timer in seconds
L4WINDOW=4 ; Level 4 window size
MAXLINKS=15 ; Max level 2 links
MAXNODES=512 ; Max nodes in nodes table
MAXROUTES=60 ; Max adjacent nodes
MAXCIRCUITS=256 ; Max L4 circuits
MINQUAL=161 ; Minimum quality to add to nodes table
; INP3 Routing is experimental. The two parms which follow will be ignored
; unless activated in the ROUTES: section.
MAXHOPS=6 ; INP3 hop limit to add to tables
MAXRTT=90 ; INP3 max RTT in seconds
BUFFERS=999 ; Packet buffers - 999 means allocate as many as
SAVEMH=1
; TNC default parameters:
PACLEN=128 ; Max packet size (236 max for net/rom)
; Level 2 Parameters:
; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section
;T3=120 ; Link validation timer in seconds
T3=900 ; will poll other nodes every 900 seconds, or 15 min.
IDLETIME=10000 ; Idle link shutdown timer in seconds
; Configuration Options:
AUTOSAVE=0 ; Saves BPQNODES.dat upon program exit
BBS=1 ; 1 = BBS support included, 0 = No BBS support
NODE=1 ; Include switch support
HIDENODES=0 ; If set to 1, nodes beginning with a #
; require a 'N *' command to be displayed.
; The *** LINKED command is intended for use by gateway software, and concern
; has been expressed that it could be misused. It is recommended that it be
; disabled (=N) if unneeded.
ENABLE_LINKED=A ; Controls processing of *** LINKED command
; Y = allows unrestricted use
; A = allows use by application program
; N = disabled
; Port Definitions:
TNCPORT
COMPORT=/home/pi/fbbded
TYPE=DED
STREAMS=1
APPLMASK=4
ENDPORT
; automatically switches bands and updates frequency every 5 seconds
RADIO 1
;Under Connectors then Data Mod set to acc
/dev/ttyICOM 19200 ICOM IC7300 94 PTT_SETS_INPUT AUX HAMLIB=4532
00:00
5,14.102300,USB,F1,D,P123
06:00
5,7.049450,USB,F1,D,P123
19:00
5,14.102300,USB,F1,D,P123
****
PORT
PORTNUM=1
ID=AFSK300 HF IL2P +850Hz
INTERLOCK=1
DRIVER=UZ7HO
CHANNEL=A
PACLEN=100
CONFIG
ADDR 44.137.31.70 8101
BEACONAFTERSESSION
UPDATEMAP
MAXSESSIONS=1
RADIO=1
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP,JO11VN,00-23,7049450,VARA500,50,35,3
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP,JO11VN,00-23,7049450,ARDOP500,50,35,3
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP,JO11VN,00-23,7049450,PKT300,50,35,3
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP,JO11VN,00-23,144850000,PKT1200,10,20,5,0
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP,JO11VN,00-23,7054000,P123,50,35,3
;WL2KREPORT PUBLIC,api.winlink.org,80,PI8LAP-10,JO11VN,00-23,7049500,ROBUST,50,35,3
ENDPORT
PORT
PORTNUM=2
ID=AFSK300 HF +1000Hz
INTERLOCK=1
DRIVER=UZ7HO
CHANNEL=B
PACLEN=100
CONFIG
ADDR 44.137.31.70 8101
BEACONAFTERSESSION
UPDATEMAP
MAXSESSIONS=1
RADIO=1
ENDPORT
PORT
PORTNUM=3
INTERLOCK=1
HIDE=0
ID=ARDOP500
DRIVER=ARDOP
CONFIG
ADDR 44.137.31.70 8515 PTT CAT
ARQBW 500MAX
LEADER 200
ENABLEPINGACK
BUSYDET 5
CONSOLELOG 3
LOGLEVEL 3
CWID TRUE
MONITOR TRUE
GRIDSQUARE JO11VN
RADIO=1
****
ENDPORT
PORT
PORTNUM=4
INTERLOCK=1
HIDE=0
ID=VARA500
DRIVER=VARA
CONFIG
ADDR 44.137.31.70 8300 PTT CAT
RADIO=1
BW500
MYCALLS PI1LAP-7 PI8LAP PI1LAP-4 PI8LAP-10
SESSIONTIMELIMIT 15
P2P SESSION
BUSYWAIT 30
****
ENDPORT
PORT
PORTNUM=5
HIDE=0
ID=BPSK300 IL2P +2150Hz
DRIVER=UZ7HO
CHANNEL=C
PACLEN=100
CONFIG
ADDR 44.137.31.70 8101
MAXSESSIONS=2
BEACONAFTERSESSION
UPDATEMAP
RADIO=1
ENDPORT
PORT
ID=Pactor SCS
COMPORT=/dev/ttySCS ; COM Port Address
SPEED=19200 ; COM Port Speed
DRIVER=SCSPactor
PORTCALL=PI8LAP
INTERLOCK=1
CONFIG ; Driver-Specific Configuration
RADIO=1
;USERAPPLCALLSFORPACTOR
****
MAXLEVEL=3
PSKA 250
FSKA 250
MARK 1600
SPACE 1400
AQ 1
STATUS 2
BUSYHOLD 1 ; This defines the time the software waits after the Controller has reported the channel free before considering it free.
BUSYWAIT 20 ; This changes the time the software will wait for a clear channel before failing a connect request.
DEBUGLOG 1 ; To activate the SCSLog_xxx_xx.txt files in the logs directory
ENDPORT
PORT
PORTNUM=7 ; Optional but sets port number if stated
ID=AX/IP/UDP ; Displayed by PORTS command
DRIVER=BPQAXIP ; Uses BPQAXIP capability of bpq32.dll
QUALITY=203 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=161 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=7 ; Max outstanding frames (1 thru 7)
FRACK=3000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=15 ; Level 2 maximum retry value
PACLEN=236 ; Max = 236
CONFIG ; BPQAXIP.cfg has been deprecated. Instead the AXIP
; configuration occurs here:
MHEARD ON ; Opens AXIP MHEARD window
;UDP 93 ; Listens for UDP packets on this UDP port number
UDP 10093
;AUTOADDMAP ; This option automatically adds the node call and
; address of a node for which you do not have a
; pre-arranged fixed entry in bpqaxip.cfg. If the
; option DONTCHECKSOURCECALL is specified then the
; AUTOADDMAP option is ignored.
BROADCAST NODES
MAP OK2PEN-5 44.63.16.*** B
MAP K5DAT-7 0.0.0.0 TCP-Slave 10200 B
MAP PI1ZTM 44.137.2.*** KEEPALIVE 180 UDP 10093 B
MAP GB7BED-5 gb7bed.****.** UDP 10093 B
MAP VE2PKT-2 44.135.49.*** B
MAP PE1NNZ 44.137.24.*** KEEPALIVE 180 UDP 10193 B
MAP OL7M SEEVER.****.*** KEEPALIVE 180 UDP 10094 B
MAP IW2OHX-15 44.134.175.*** KEEPALIVE 180 UDP 10093 B
MAP PD0LPM-9 213.10.245.*** KEEPALIVE 180 UDP 10093 B
MAP PA8F-2 44.137.1.*** KEEPALIVE 180 UDP 10093 B
MAP PD9Q 44.137.31.*** KEEPALIVE 180 UDP 10093 B
MAP F8COD-2 80.119.24.*** KEEPALIVE 180 UDP 10093 B
ENDPORT
PORT
PORTNUM=8 ; Optional but sets port number if stated
ID=Telnet
DRIVER=Telnet
CONFIG
LOGGING=1
DisconnectOnClose=1
CMS=1
CMSCALL=PI8LAP
CMSPASS=*******
CMDPORT=7300 7301 6001 6002
CMSLOGGING=1
FALLBACKTORELAY=1
; RELAYHOST=127.0.0.1
RELAYAPPL=BBS
TCPPORT=6370
FBBPORT=6380
HTTPPORT=8081
; SNMPPORT=161
SECURETELNET=1
LOGINPROMPT=User:
PASSWORDPROMPT=Password:
MAXSESSIONS=10
CTEXT=Welcome to PI1LAP Telnet Server.\nPress ? For list of commands \n\n
USER=pd9q,******,pd9q,,SYSOP
USER=pi8lap,******,pi8lap,,SYSOP
ENDPORT
;PORT
; PORTNUM=9
; ID=AFSK 300Baud QO-100 RX-only
; DRIVER=UZ7HO
; CHANNEL=A
; CONFIG
; ADDR 192.168.1.212 8101
; UPDATEMAP
; MAXSESSIONS=1
;ENDPORT
;PORT
; PORTNUM=10
; ID=BPSK 1200Baud QO-100 RX-only
; DRIVER=UZ7HO
; CHANNEL=B
; CONFIG
; ADDR 192.168.1.212 8101
; UPDATEMAP
; MAXSESSIONS=1
;ENDPORT
PORT
PORTNUM=9 ; Optional but sets port number if stated
ID=144.850Mhz FM 1k2 ; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
FULLDUP=0 ; Only meaningful for KISS, JKISS or BPQKISS devices
IPADDR=44.137.31.76
TCPPORT=8001 ; 1 = SERIAL PORT COM1 ETC.
CHANNEL=A ; A for single channel TNC, A or B for multichannel
PERSIST=160 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=180 ; CMSA interval timer in milliseconds
TXDELAY=270 ; Transmit keyup delay in milliseconds
TXTAIL=23 ; TX key down, in milliseconds, at packet end
QUALITY=203 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=201 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=7 ; Max outstanding frames (1 thru 7)
FRACK=5000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=25 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=APBPQ1,WIDE1-1 ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=PI1LAP-7 ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digid frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
ENDPORT
PORT
PORTNUM=10 ; Optional but sets port number if stated
ID=144.800Mhz FM Aprs ; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
IPADDR=44.137.31.76
TCPPORT=8001
CHANNEL=B ; A for single channel TNC, A or B for multichannel
NOKEEPALIVES=1
PERSIST=160 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=180 ; CMSA interval timer in milliseconds
TXDELAY=270 ; Transmit keyup delay in milliseconds
TXTAIL=23 ; TX key down, in milliseconds, at packet end
QUALITY=0 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=201 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=7 ; Max outstanding frames (1 thru 7)
FRACK=5000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=25 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=APBPQ1,WIDE1-1 ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=PI1LAP-7 ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=1 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digid frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
ENDPORT
PORT
PORTNUM=11
ID=Robust 600Baud ;(RPR and HF Packet)
TYPE=EXTERNAL
COMPORT=/dev/ttyTRK
SPEED=38400
DRIVER=SCSTracker
INTERLOCK=1
CONFIG
****
M UISC
O 4 ; MAXFRAME
F 190 ; FRACK
T 8 ; TX Delay
FORCE ROBUST
DEFAULT ROBUST ; Default mode is RP
USEAPPLCALLS ; Accept connects to all APPLCALLS
BEACONAFTERSESSION ; Beacon after session
%L 1500 ; Centre Freq for Normal Packet (Default is 1500)
@I 64 ; Paclen = 60
%T 1 ; TX Autotracking 1 = on
%N 10
%B R600
ENDPORT
ROUTES: ; Locked routes (31 maximum)
; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN,INP3Enable]
; PD9Q-15,203,7,0,0,0,0
*** ; Denotes end of locked routes
;IPGATEWAY
; Adapter eth0
; IPADDR 44.137.31.84
; IPNETMASK 255.255.255.224
; ;ENABLESNMP
;****
APRSDIGI
DISTKM=1
APRSCall=PI1LAP-8
StatusMsg=PI1LAP-8 ARPS DIGI JO11VN ZLD
Symbol=n ; Icon to display for station.
Symset=/ ; This is a "B" in a Red Diamond.
;
; Specify a Dest Addreess and Path for each port you want to use for APRS. No dest means receive only port
; Ports without an APRSPath statement will not be used by the Digi
;
; Note if you specify APRS as the destination call it will be replaced by the current BPQ32 APRS
; identification destination - APBPQ1. If you really want to send APRS, specify APRS-0.
; APRSPath 1=APRS,WIDE1-1 ; Dest and up to 8 digis
; APRSPath 3=APRS,WIDE1-1
APRSPath 10=APRS,WIDE1-1
; APRSPath 9=APRS,WIDE1-1
BeaconInterval=25 ; Send Beacon every 30 minute. Minimum is 5 mins
MAXAGE=120
; Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
; If a Digimap isnt specified for a port, digi out on the port the packet arrived on,
; and send to APRS-IS (if enabled)
; If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n
; If you dont want to digi on a port, specify Digimap n=
;
; If you only have one APRS port, you probably dont need a Digimap statement
; Digimap 1=1,IS ; Packets from 1 to 9, but not APRS-IS
; Digimap 3=3,IS
Digimap 10=10,IS
; Digimap 9=9,IS
; Define Digipeating parameters
TraceCalls=WIDE,TRACE ; Calls for CALLN-n Processing with Trace
FloodCalls=NLD ; Calls for CALLN-n Processing without Trace
DigiCalls=PI1LAP-8 ; Calls for Normal (ie no SSID manipulation) Digi
; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
;ReplaceDigiCalls ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
MaxTraceHops=2 ; Max value of n in CALLN-n processing. If a packet is received with n greater than
MaxFloodHops=2 ; this, the value will be replaced BEFORE it is decremented.
; Specify position. You can specify a fixed LAT/LONG, or use GPS
LAT=5133.52N ; Must be in standard APRS Format (ddmm.mmN/S)
LON=00348.15E ; Must be in standard APRS Format (dddmm.mmE/W)
GPSPort=/dev/ttyUSB0 ; if specified, lat/lon will be taken from a GPS,
GPSSpeed=9600 ; overriding the values set above.
; The Digi can generate Object and Item reports.
; The format is pretty strict - a single space between param=value pairs,
; a comma but no spaces in PATH and PORT string.
; Minimum interval is 10 mins. You can have as many OBJECT lines as you need.
; See thr APRS specification for information on how to format an Object or Item string.
; OBJECT PATH=APRS,WIDE1-1 PORT=1 INTERVAL=10 TEXT=;PD9Q*111111z5133.52N/00348.15EIPD9Q-10 Linbpq APRS Station
; OBJECT PATH=APRS,WIDE1-1 PORT=3 INTERVAL=14 TEXT=;PI1LAP-8*111111z5133.52N/00348.15EIPI1LAP-8 ((Lin)bpq) APRS Station NLD
OBJECT PATH=APRS,WIDE1-1 PORT=10 INTERVAL=16 TEXT=;PI1LAP-8*111111z5133.52N/00348.15EIPI1LAP-8 ((lin)BPQ) APRS Station NLD
; OBJECT PATH=APRS,WIDE1-1 PORT=2 INTERVAL=17 TEXT=;PI1LAP-10*111111z5133.52N/00348.15EIPI1LAP-10 ((Lin)BPQ) APRS Station
; IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS
ISHost=euro.aprs2.net
ISPort=14580 ; Normal port for a filtered feed
ISPasscode=**** ; If you dont already have a passcode I can issue you one
;
; You can specify a filter command to be sent when you log on to APRS-IS. Normally you dont
; need one. The APRS Mapping Application (BPQAPRS) sets a filter when it starts,
; and if you arent running an APRS application, there isnt much point in getting info from APRS-IS
;
;ISFilter=m/500 ; Filter Command if needed
; WXCall=PI1LAP-8
; WXFileName=/home/pi/linbpq/current.txt
; WXComment=/PI1LAP-8 Weather Station JO11VN
; WXPortList=6,9,IS ; comma separated list - include IS to send to APRS-IS
; WXInterval=18 ; mins
;
****
LINMAIL
LINCHAT
APPLICATION 1,BBS,,PI8LAP,LAPBBS,255
APPLICATION 2,CHAT,,PI1LAP-4,LAPCHT,255
APPLICATION 3,DXC,C 8 HOST 0 S,PI1LAP-2,LAPDXC,255
APPLICATION 4,RMS,C 8 CMS,PI8LAP-10,LAPRMS,255
;APPLICATION 5,RMS,C 11 ON0SEA-10,PI8LAP-10,LAPRMS,255
APPLICATION 6,SYSINFO,C 8 HOST 1 S
Related
