Hier onder de configuratie die ik gebruik voor Linbpq.
/*
Packet/Switch netwerk Kortgene.
*/
LOCATOR=JO11VN
MAPCOMMENT=PI1LAP Network Node, Kortgene JO11VN
PASSWORD=**********
NODECALL=PI1LAP-15 ; Node callsign
NODEALIAS=LAPNET ; Node alias (6 characters max)
IDMSG:
Winlink Gateway PI1LAP-10
***
BTEXT: ; UI broadcast text from BCALL to destination UNPROTO=
=5133.52N/00348.15En PI1LAP-15 Switch Node, BBS/APRS/AMPR/DXspider/RMS-(PI1LAP-10) Gateway.
***
INFOMSG: ; The INFO command text follows:
PI1LAP LinBPQ Packet/Switch Node
Computer : Optiplex GX280
Software : Debian GNU/Linux 7 3.2.0-4-686-pae / Linbpq 6.0.13.1
Rx/Tx : Kenwood IC-F1010 / Yaesu FT7800
Modem : Mfj 1278b / tnc7multi
Antenne : X50n / X30n
Sysop Niels Ruiter
Ax25-mail : pd2lt@pi8lap.#zl.nld.euro
AMPR mail : pd2lt@pi1lap.pd2lt.ampr.org
E-mail : pd2lt@packet-radio.net
Have Fun
***
CTEXT: ; The CTEXT text follows:
Connected to PI1LAP-15.
Packet/Switch Node, Kortgene JO11VN
RMS : Winlink packet Gateway
Dx : Dxspider Cluster
LAPNET:PI1LAP-15} APP,RMS,DX,CHAT,C,B,I,N,R,P,U,V,S,MH
*** ; Denotes end of CTEXT text
FULL_CTEXT=1 ; 0=send CTEXT to L2 connects to NODEALIAS only
; 1=send CTEXT to all connectees
OBSINIT=6 ; Initial obsolescence set when a node is included
; in a received nodes broadcast. This value is then
; decremented by 1 every NODESINTERVAL.
OBSMIN=4 ; When the obsolescence of a node falls below this
; value that node's information is not included in
; a subsequent nodes broadcast.
LogL4Connects=1
NODESINTERVAL=15 ; Nodes broadcast interval in minutes
IDINTERVAL=10 ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
BTINTERVAL=60 ; The BTEXT broadcast interval in minutes, 0=OFF
L3TIMETOLIVE=25 ; Max L3 hops
L4RETRIES=3 ; Level 4 retry count
L4TIMEOUT=60 ; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=10 ; Level 4 delayed ack timer in seconds
L4WINDOW=4 ; Level 4 window size
MAXLINKS=63 ; Max level 2 links
MAXNODES=1024 ; Max nodes in nodes table
MAXROUTES=128 ; Max adjacent nodes
MAXCIRCUITS=1024 ; Max L4 circuits
MINQUAL=100 ; Minimum quality to add to nodes table
; INP3 Routing is experimental. The two parms which follow will be ignored
; unless activated in the ROUTES: section.
MAXHOPS=10 ; INP3 hop limit to add to tables
MAXRTT=90 ; INP3 max RTT in seconds
BUFFERS=255 ; Packet buffers - 255 means allocate as many as
; possible, normally about 130, depending upon other
; table sizes.
; TNC default parameters:
PACLEN=128 ; Max packet size (236 max for net/rom)
; Level 2 Parameters:
; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section
T3=120 ; Link validation timer in seconds
IDLETIME=10000 ; Idle link shutdown timer in seconds
; Configuration Options:
AUTOSAVE=1 ; Saves BPQNODES.dat upon program exit
BBS=1 ; 1 = BBS support included, 0 = No BBS support
NODE=1 ; Include switch support
HIDENODES=1 ; If set to 1, nodes beginning with a #
; require a 'N *' command to be displayed.
; The *** LINKED command is intended for use by gateway software, and concern
; has been expressed that it could be misused. It is recommended that it be
; disabled (=N) if unneeded.
ENABLE_LINKED=A ; Controls processing of *** LINKED command
; Y = allows unrestricted use
; A = allows use by application program
; N = disabled
; Port Definitions:
PORT
PORTNUM=1 ; Optional but sets port number if stated
ID=144.850Mhz ; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
FULLDUP=0 ; Only meaningful for KISS, JKISS or BPQKISS devices
COMPORT=/dev/ttyUSB0
SPEED=9600 ; RS232 COM PORT SPEED
CHANNEL=A ; A for single channel TNC, A or B for multichannel
NOKEEPALIVES=0
PERSIST=160 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=180 ; CMSA interval timer in milliseconds
TXDELAY=180 ; Transmit keyup delay in milliseconds
TXTAIL=23 ; TX key down, in milliseconds, at packet end
QUALITY=192 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=100 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=4 ; Max outstanding frames (1 thru 7)
FRACK=5000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=25 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=APBPQ1,PI1LAP ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=PI1LAP-15 ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
ENDPORT
PORT
PORTNUM=2 ; Optional but sets port number if stated
ID=430,950MHz ; Displayed by PORTS command
TYPE=ASYNC ; Port is RS232 Com
PROTOCOL=KISS ; TNC is used in KISS, JKISS or BPQKISS mode
FULLDUP=0 ; Only meaningful for KISS, JKISS or BPQKISS devices
COMPORT=/dev/ttyUSB0
SPEED=9600 ; SERIAL PORT SPEED, NOT RADIO DATA SPEED.
CHANNEL=B ; A for single channel TNC, A or B for multichannel
PERSIST=255 ; PERSIST=256/(# of transmitters-1)
SLOTTIME=100 ; CMSA interval timer in milliseconds
TXDELAY=300 ; Transmit keyup delay in milliseconds
TXTAIL=30 ; TX key down, in milliseconds, at packet end
QUALITY=192 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
; With QUALITY=0, the value of MINQUAL is irrelevant
MINQUAL=100 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=4 ; Max outstanding frames (1 thru 7)
FRACK=5000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=25 ; Level 2 maximum retry value
PACLEN=128 ; Default max packet length for this port
UNPROTO=APBPQ1,PI1LAP ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
BCALL=PI1LAP ; BTEXT call. unstated defaults to APPL1CALL
L3ONLY=0 ; 1=No user downlink connects on this port
DIGIFLAG=1 ; Digipeat: 0=OFF, 1=ALL, 255=UI Only
DIGIPORT=0 ; Port on which to send digi'd frames (0 = same port)
USERS=0 ; Maximum number of L2 sessions, 0 = no limit
ENDPORT
; AX/IP/UDP port definition.
PORT
PORTNUM=3 ; Optional but sets port number if stated
ID=AX/IP/UDP ; Displayed by PORTS command
DRIVER=BPQAXIP ; Uses BPQAXIP capability of bpq32.dll
QUALITY=255 ; Quality factor applied to node broadcasts heard on
; this port, unless overridden by a locked route
; entry. Setting to 0 stops node broadcasts
MINQUAL=192 ; Entries in the nodes table with qualities greater or
; equal to MINQUAL will be sent on this port. A value
; of 0 sends everything.
MAXFRAME=7 ; Max outstanding frames (1 thru 7)
FRACK=3000 ; Level 2 timout in milliseconds
RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds
RETRIES=5 ; Level 2 maximum retry value
PACLEN=236 ; Max = 236
CONFIG ; BPQAXIP.cfg has been deprecated. Instead the AXIP
; configuration occurs here:
MHEARD ON ; Opens AXIP MHEARD window
UDP 10094 ; Listens for UDP packets on this UDP port number
; UDP 93 ; Listens for UDP packets on this UDP port number
; AUTOADDMAP ; This option automatically adds the node call and
; address of a node for which you do not have a
; pre-arranged fixed entry in bpqaxip.cfg. If the
; option DONTCHECKSOURCECALL is specified then the
; AUTOADDMAP option is ignored.
BROADCAST NODES
BROADCAST QST
MAP PI1SNK ip-adres pi1snk UDP 10094
MAP PI1DXC-15 ip-adres pi1dxc UDP 93 B
MAP PI1DEC-14 ip-adres pi1dec UDP 93
MAP PI1LAP ip-adres link local UDP 93 B
ENDPORT
; Radio port definitions.
PORT
PORTNUM=4 ; Optional but sets port number if stated
ID=Telnet
DRIVER=Telnet
PORTCALL=PI1LAP-10
CONFIG
CMS=1
CMSCALL=PI1LAP
CMSPASS=********
LOGGING=1
DisconnectOnClose=1
CMDPORT 7400 63000
TCPPORT=6323
FBBPORT=6300
HTTPPORT=9180
LOGINPROMPT=User:
PASSWORDPROMPT=Password:
MAXSESSIONS=10
CTEXT=Welcome to PI1LAP`s Telnet Server.\nPress ? For list of commands \n\n
USER=pd2lt,********,PD2LT,,SYSOP
USER=pd2nlx,*******,PD2NLX,,SYSOP
ENDPORT
PORT
PORTNUM=5
ID=LOOPBACK
TYPE=INTERNAL
PROTOCOL=KISS
CHANNEL=A
QUALITY=255
MAXFRAME=6
FULLDUP=0
FRACK=10000
RESPTIME=3000
RETRIES=10
PACLEN=200
TXDELAY=500
SLOTTIME=100
PERSIST=64
DIGIFLAG=1
UNPROTO=APBPQ1,PI1LAP-11
BCALL=PI1LAP-15
ENDPORT
PORT
PORTNUM=6
ID=Link tnn
TYPE=ASYNC
PROTOCOL=KISS
QUALITY=255
COMPORT=/dev/com6
CHANNEL=A
SPEED=9600
MAXFRAME=7
FRACK=5000
RESPTIME=1000
RETRIES=10
PACLEN=128
ENDPORT
;PORT
; PORTNUM=7
; ID=Link RMS
; TYPE=ASYNC
; PROTOCOL=KISS
; QUALITY=255
; COMPORT=/dev/com7
; CHANNEL=A
; SPEED=9600
; MAXFRAME=6
; FRACK=5000
; RESPTIME=1000
; RETRIES=10
; PACLEN=236
;ENDPORT
ROUTES: ; Locked routes (31 maximum)
; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN,INP3Enable]
PI1SNK,1,3,1,0,0,1
PI1DXC-15,255,3
PE1PLM-14,192,1
PI1LAP,1,1,0,0,0,1 ; BPQ AX/UDP on Multiple_Apps System
*** ; Denotes end of locked routes
;
IPGATEWAY
Adapter eth0 # Linux
44ENCAP 192.168.1.220 # Enable AMPRNET Tunnels and RIP44
IPAddr 44.137.31.70 # IP address of BPQ32
IPNetmask 255.255.255.224 # Netmask
IPPorts 1,3 # BPQ Ports to be used for links to IP systems. List of ports, separated by commas
;NAT 44.137.31.66 192.168.1.238 # inet.pd2lt.ampr.org (www,ftp)
;NAT 44.137.31.81 192.168.1.222 # hamnet.pd2lt.ampr.org (hamnet access)
;NAT 44.137.31.67 192.168.1.112 # jnos.pd2lt.ampr.org (jnos)
;NAT 44.137.31.67 192.168.1.222 # aprs.pd2lt.ampr.org (aprsc server)
;NAT 44.137.31.69 192.168.1.213 # sys1.pd2lt.ampr.org (windows 7)
;ARP 44.131.31.67 PI1LAP-2 1 D # 44.131.56.6 is reachable over radio port 1
;ARP 44.137.31.67 PI8LAP-1 1 D
;ARP 44.147.31.67 PI1LAP-14 3 D
ARP 44.137.56.106 PI1SNK 3 D # ARP entry for Gateway below
ROUTE 44.137.56.0/22 44.137.56.106 # All subnet 44.131.11.0/29 is reachable over radio link 1 to GM8BPQ-7
route addprivate 44.137.31.64/27 encap 82.176.25.213 # AMPRNET Tunnel route
;route addprivate 44.137.31.72/29 encap 149.210.235.143 # Link vpn ipip tunnel vpn-server
;route addprivate 44.137.31.89/29 encap 149.210.215.162 # Link www server tunnel vps
*****
APRSDIGI
APRSCall=PI1LAP-11
StatusMsg=PI1LAP-11 APRS Digi RX-only .
Symbol=& ; Icon to display for station.
Symset=I ; This is a "B" in a Red Diamond.
;
; Specify a Dest Addreess and Path for each port you want to use for APRS. No dest means receive only port
; Ports without an APRSPath statement will not be used by the Digi
;
; Note if you specify APRS as the destination call it will be replaced by the current BPQ32 APRS
; identification destination - APBPQ1. If you really want to send APRS, specify APRS-0.
;APRSPath 2=APRS ; Receive only port
APRSPath 1=APRS,WIDE1-1,WIDE2-1 ; Dest and up to 8 digis
; APRSPath 2=APRS,WIDE1-1,WIDE2-1
APRSPath 5=APRS,WIDE1-1,WIDE2-1
BeaconInterval=20 ; Send Beacon every 30 minute. Minimum is 5 mins
MAXAGE=120
MobileBeaconInterval=2 ; Beacon interval when moving
; Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
; If a Digimap isn't specified for a port, digi out on the port the packet arrived on,
; and send to APRS-IS (if enabled)
; If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n
; If you dont want to digi on a port, specify Digimap n=
;
; If you only have one APRS port, you probably don't need a Digimap statement
Digimap 1=1,IS ; Packets from 1 to 9, but not APRS-IS
Digimap 5=5,IS ; Packets from 7 to 7, 9 and APRS-IS
; Digimap 2=2,IS
; Define Digipeating parameters
TraceCalls=WIDE,TRACE ; Calls for CALLN-n Processing with Trace
FloodCalls=NLD ; Calls for CALLN-n Processing without Trace
DigiCalls=ZLD ; Calls for Normal (ie no SSID manipulation) Digi
; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
;ReplaceDigiCalls ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
MaxTraceHops=2 ; Max value of n in CALLN-n processing. If a packet is received with n greater than
MaxFloodHops=2 ; this, the value will be replaced BEFORE it is decremented.
; Specify position. You can specify a fixed LAT/LONG, or use GPS
LAT=5133.52N ; Must be in standard APRS Format (ddmm.mmN/S)
LON=00348.15E ; Must be in standard APRS Format (dddmm.mmE/W)
;GPSPort=/dev/ttyUSB1 ; if specified, lat/lon will be taken from a GPS,
;GPSSpeed=4800 ; overriding the values set above.
; The Digi can generate Object and Item reports.
; The format is pretty strict - a single space between param=value pairs,
; a comma but no spaces in PATH and PORT string.
; Minimum interval is 10 mins. You can have as many OBJECT lines as you need.
; See thr APRS specification for information on how to format an Object or Item string.
OBJECT PATH=APRS,WIDE1-1,WIDE2-1 PORT=1,IS INTERVAL=10 TEXT=PI1LAP*111111z5133.52N/00348.15EIPI1LAP Switch Node, BBS/APRS/AMPR/DXspider/RMS-(PI1LAP-10) Gateway.
; IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS
ISHost=194.109.192.235 ; APRS-IS Host Name. May be either an IPV4 or an IPV6 Host
ISPort=14580 ; Normal port for a filtered feed
ISPasscode=******* ; If you don't already have a passcode I can issue you one.
;
; You can specify a filter command to be sent when you log on to APRS-IS. Normally you don't
; need one. The APRS Mapping Application (BPQAPRS) sets a filter when it starts,
; and if you aren't running an APRS application, there isn't much point in getting info from APRS-IS
;
ISFilter=m/500 ; Filter Command if needed
; Bridge 1=6
; Bridge 6=1
****
LINMAIL
LINCHAT
APPLICATION 1,BBS,,PI8LAP,LAPBBS,255
APPLICATION 2,CHAT,,PI1LAP-6,LAPCHT,255
APPLICATION 3,RMS,C 4 CMS,PI1LAP-10,LAPRMS,255
APPLICATION 4,DX,C 4 HOST 0 S,PI1LAP-4,LAPDX,255
APPLICATION 5,APP,C 4 HOST 1 S
APPLICATION 6,TNN,C 6 PI1LAP,255
APPLICATION 32,SYSOP
